Although it felt better in the heat of the shop during the build, I’m paying for wearing only a short sleeve shirt during all of that welding.

All that’s left in the front is to weld up a flat bracket on the cross-member for the motor mount to bolt through. Once motor is mounted with the frame sitting at "ride stance", the proper height of the tranny mount can be determined placing a level on the intake manifold and a jack under the tailshaft. As you probably know, the carbs have to be level for the floats to work right and this will be the done by trans mount location.

Once the drive-line angle is dictated (again, from the tranny mount) you’re able to determine the rear-end pinion angle and drive-shaft length. From there it’s just one relaxing, fun time after another of nuts, bolts, lines & wiring.

The body isn’t sitting on any mounts yet because I think the owner is still considering enough of a channel-job to hide the rails, but that’ll be dictated by his interior room comfort level. I think he’s in the thought process of sitting in it & trying it on "as-is" since we delivered it back to his hangar. (Maybe even making "Vroom, Vroom" noises 8-) )

Whichever way he goes with the channel will really have nothing to do with the running-gear work already mentioned and can be done at his leisure.

and a few more pics in The Gallery.

I noticed when I was working with some images that The Gallery Page wasn’t listing the different projects, etc. I recently updated the server software for that feature and the chage must’ve happened at some point at that time.

The issue has been corrected and I’m working on rebuilding some albumsf, but the more popular ones have been re-added to The Gallery Page.

Click Images to Enlarge

Last night after getting home from a 12hr shift at 7:30, I pretty much had made up my mind to pull an all-nighter to get this done and started by lifting the engine out so I’d have room to get to the front cross-member and boxing plates.

and with it out of the way, I could also get a final trim on the rails

Without exaggeration, after these last few days and getting off work I welded until I started to go so cross-eyed from the steady intense focusing that I wasn’t following my bead and my hand went numb at the trigger (You don’t get a break at the end of each stick when you’re using a wire-feed welder with a 10lb spool) but it wasn’t until after the heat got to be too much through the gloves the I decided to give the welder a break and sit back. 

Since I hadn’t looked at the clock beforehand, I couldn’t tell you how long it was, but when I realized that I had fallen asleep sitting on the floor between the rails, I got up, took a shower and went to bed. When I woke back up in the afternoon, nobody was home so I went back at it to finish what was left. I think I finished by 4 or 5 PM

The End.

More pics of this build in The Gallery

I’ve got everything square and welded so it can’t move (better than tacked but not completely finished). The upper rails we were discussing have been removed and the wheelbase is stretched 2".

You can see the where the original frame rails need to be boxed in. I’ll be doing the whole frame while I’m off in a few days. I just threw the tranny crossmember on top and will have to cut it down to fit while I’m working on boxing the frame.

The gray vertical pipes in the pictures is my portable hoist frame. I set it up tonight in anticipation of lifting the engine out tomorrow to do the front boxing plates. If you look at the front cross-member in the pic below, you’ll notice the original rivet holes and that it’s not riveted to the frame. When I installed the front drop axle, I had to widen the frame ~ 1 1/2" to mount things up. I’ll widen this piece too, and get it back in while I’m off.

It’s almost 9" lower than stock now. There’s work to do on that Hemi but I’m not getting into that right now. I just needed it to fit and fabricate the motor and transmission mounts.

Leaving the overhead door down to keep the late night disturbance of the neighbors to a minimum, I hadn’t realized how smoky the shop had become, but I thought I’d post some pics…

This is as far as I made it by midnight tonight:

I cut and fabricated the new, lower rails and welded them to the front original rails. It’s an 8 1/2" drop. The 3 Jack stands are supporting the transmission and both back rails since I was just getting ready to cut out the center section and slide the front & rear originals apart 2" to stretch the wheelbase… but I decided that since I need to get up to go to work for another 12hr shift that 4:30 is going to come quickly and enough is enough for one night.